Відео

You da man!!!

Safe trip

I just did my "79. What an absolute bastard of a job, must have had that off and on about 20-30 times! Had to leave off the inner over riders, no way they were going to fit up with the new bumper!

Chrome paint and no one would know

Thanks you for this.

This has been very informative to me. I've had my '67 since 1987. The body was pieced together before I bought it and I've always wondered what the heck was going on with some of the weird fits. Your video has helped me answer many of my questions. Don't know if I'll ever correct them but I've learned a few tricks from you that will help if I decide to tackle any of them. Thank you.

If you get a hood and it fits it’s not a corvette.

My Auntie bought one off the showroom floor for $5500 and i believe it had 2x4barrels originally,it was also a convertible, & i know it was a blue color... I've heard naysayers say they didn't come out until 67'

My original headlight bar came completely unbonded. I got 3 broken relay bolts, rusted in, but got them soaking in penetrating oil for a week. I still have to remove the surface rust, treat for corrosion, and re-paint. How much is this carbon fiber headlight bar? I just might want to upgrade my 1981 vette.

Do you build a LT1 hood for a 1969 Corvette?

I have some debonding issues on a 81 vette, and i think your product is what i need. How much is it, and how can I get it. This vette was shaken very baddly. Driven up and down a 5 mile dirt road at 50 and 60 mph, both ways. It's got a few debonding issues at the body and inner fender wheels, and cracks at front and back fenders. Any tips you can give, I'll be forever grateful.

If i lived in Saginaw

How are the bonding strips made?

Did you modify the hubs to fit the wheels ?

I love these videos that school us in the correct way to do a nice job. Thanks for sharing these with us Steve!!! Tux Hadler / Simply Corvettes...

Thanks for the lesson Steve!

Where are you from arlin

Is the center the only part that is carbon fiber ?

Fantastic!

Is the foam comfortable for long trips? Is it the leather cover set for a C6 ordered for this setup? Thanks, Chuck Corvette Repairs of Maine

Just got that kit in. Thank you.

Lookin good!

Would love to see more of this car. Absolutely love it!

This is a good place to do business with… Great customer service everytime I need corvette adhesive’s or hardware!! I replaced my left rear qtr panel without ever doing any corvette bodywork ever. I watched this man’s videos and purchased his two part cans of adhesive and my finished product was amazing and absolutely perfect. SIDE NOTE, I’d totally marry this man’s daughter!!!

Is it a real body?!?!?! Fiberglass repro please lol

I've got a 76 i would love to do this to. But how extensive does it get? Seems like ot would be a whole lot of custom fab work

A bonding strip in a place the factory did not use it screams damaged and then repaired. It can also be top glassed then back glassed leaving NO SIGNS of repair. Retaining the cars value as it will never crack out and the repair will never be seen. P.S. We went through the same issue putting GM factory Quarters on 1973 cars. My father called GM and they admitted they had changed the body material to get parts out of the molds easier. Those rear quarter panels we learned quickly were unrepairable using standard fiberglass. I am not implying your repair isn't permanent or quality but it is discoverable possibly devaluing the car.

Thank you for showing all of these steps! I have a 61 that has a few areas that need repaired. Your videos show that it can be done!

Can you send me what the body mounts look like. My friend is rebuilding one now. Stuck at this point.

I want to take you my c3 now ..

You're an amazing man!.. over 50 years of your Pro experience here is INVALUABLE!!!

Thank you for the video. Do you have any videos on how the brackets go on the vehicle. I am restoring one and can't find any information. Thank you!

wow, I had a ´65 that my father had purchased brand new and I had sent the bumpers to San Diego to be rechromed around 1994. They came back great but I remember how heavy they were. I was searching for how to plate carbon fiber and found this video. (I got arrested for family court and had to sell the vette to pay for the lawyer) I am looking for it years later.

🟥 The man is a world of knowledge. 👍👍👍

A little late to comment ...excellent tips Steve ...but ..concerned for your health in this repair you are grinding away without a mask . Do not mean to tell you what to do , knowing that you are aware of it ...that stuff is awful for the lungs.

Do you sell one that is easy to mount (Pre-Cut) with Bumpers?

Always great! Thank you.❤ More please.

Always great. Thank you❤ More please

Great stuff guys

I wish y'all made widebody fenders for 80-82 body style. Not everyone wants their C3 to look like a 69.

Could you use a heat gun to speed up the curing of the epoxy?

Thanks for the Shim Trick & cool Rear Deck Lid look! Instead of me buying a standard HardTop for my C2, which is just ok... Has anyone ever heard of a C2 HardTop being Molded to the Shape of the beautiful Coupe. I know its a crazy idea because of a long size, but if left on - it could transform our Convertibles!

Excellent, Soon!

Is this system available and Price range? Thanks

Has this been completed?

how long does it take for you guys to do this replacement start to finish?

Beautiful job. What product do you use for your gaps. Also what primers do you use. Im trying to learn what brands and materials i need to do my c2. Im doing a full frame off and getting ready for the Body work. First time doing this. Would greatly appreciate what brands of materials you use. Thanks

I really like how you did the quarter panel install 😊

Thanks for the inside scoop 😊 what kind of epoxy are you using

So can I use this expoxy to glue a quarter panel on